SPECIFICATION FOR APPROVAL

Anuncio
SPECIFICATION FOR APPROVAL
CUSTOMER NAME :
PART
No.
HP10
:
ISSUE DATE
:
2015-05-14
ACCESSORY
:
2015050014
APPROVED SIGNATURES
QUALITY DEPT.
ENGINEERING DEPT.
PRODUCER
■ Mechanical Dimensions:
Note:
1. All dimensions are in millimeters.
2. All dimensions without tolerances are for reference only.
3. Material as follows:
Package:
Heat-Resistant Polymer
Electrodes:
Cu Plating Copper Alloy
■Absolute Maximum
Ratings (Ta = 25℃) :
Items
Absolute maximum Rating
Symbol
Write
Unit
DC Forward Curren
IF
1050
mA
Peak Pulse Forward Current*
IFP
1400
mA
Reverse Voltage
VR
5
V
LED Junction Temperature
Tj
100
℃
Operating Temperature
Top
-40 ~ +80
℃
Storage Temperature
Tstg
-40 ~ +100
℃
Soldering Temperature
Tsol
Max.260°C for10sec Max
*Pulse width≦0.1msec duty≦1/10
■ Typical Electrical & Optical Characteristics ( Ta = 25℃):
Part No
Color
Temperature
QG-ZB-10W 6000-6500K
Forward Voltage(V)
Min.
Typ.
Max.
9
--
12
■Notes:
1.Absolute maximum ratings Ta=25℃.
2.Tolerance of measurement of forward voltage±0.1V.
3.Tolerance of measurement of Luminous Flux ±15%.
Viewing
Ra(≥ Luminous Flux
Angle
(lm)
)
(Typ.)
IF =1050mA
120
70
800-900LM
Test
Condition
■ Typical
Electrical/ Optical Characteristics Curves
(Ta=25°C Unless Otherwise Noted) :
Forward Current Characteristics
800
140
700
120
Relerive Light Output(%)
Normalized Relative Luminous Flux
900
600
500
400
300
200
100
0
200
400
600
800
100
80
60
40
20
0.0
1000
-30
IF-Average Forward Current(mA)
30
60
90
120
Junction Temperatrue,Tj(c)
900
100
800
700
75
Wavelenght Characteristics
IF-Average Forward Current(mA)
0
600
500
400
300
200
100
4
6
8
10
12
VF- Forward Voltage(V)
14
16
50
25
0
400
450
500
550
Wavelength(nm)
600
650
■ Reliability
1.Test Items And Results
Classification
Test Item
Operation
Test
Operating Life
Test
High Temperature
Storage
Low Temperature
Storage
Environment
Temperature. &
Test
Humidity Storage
Thermal Shock
Soldering
Test
Test Conditions
Duration
Units
Tested
Number
of
Damaged
TA=25℃±5℃,IF=1050mA
1000 Hrs
22
0/22
TA=100℃±5℃
1000 Hrs
22
0/22
TA=-40℃±5℃
1000 Hrs
22
0/22
1000 Hrs
22
0/22
22
0/22
22
0/22
22
0/22
Reference
Standard
JEITA ED-4701
200 201
JEITA ED-4701
200 201
TA=85℃±5℃,
RH=85%±5%RH
JEITA ED-4701
300 307
-40°±5℃ +85℃±5℃
30min dwell / 5 min transfer
Solder ability
220±5℃,30 ±1 sec
Resistance to
Soldering Heat
260±5℃,10 ±1 sec
20
Cycles
1 time
Over
95%Wetting
1 time
2.Failure criteria
-
-
-
Electrical Failures:
-
VF shift% >10%
-
IR(VR=5V)>100uA
-
Flux Degradation% > 50% max ;> 35% average
-
Broken or damaged package or lead
-
Solder ability < 95% Wetting
-
Dimension out of tolerance
-
Discolor of lens
Light Output Degradation:
Visual Failures:
■ Note:It is required that the LEDs should be attached heat-sink when these LEDs are Operating.
Documentos relacionados
Descargar