Parent code -0.1-0.2-0.3-0.4-0.5-0.6-0.7-0.8-0.9- -1.0- -1.1- -1.2- -1.3- -1.4- -1.5-1.6-1.7-1.8-1.9-2.0-2.1-2.2-2.3-2.4-2.5-2.6-2.7-2.8-2.9-3.0-3.1-3.2-3.3-3.4-3.5-3.6-3.7-3.8-9.1-9.5-9.6-9.7-9.8- No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 FORM 1 Content Subitem code 8N1 1:8N1 3:8E1 2:8N2 4:801 35.0~99.0Hz Software version number Hardware version number Reset MCU Restore default value Segment speed 0 setting Rated speed of motor Motor slip Polar logarithm Braking coefficient Braking time Braking frequency at stop Undefined (customizable) Current display selection Undefined (customizable) Operating arrival frequency Segment speed 7 setting Segment speed 6 setting Segment speed 5 setting Segment speed 4 setting Segment speed 3 setting Segment speed 2 setting Display flashing - 8.88, press start / stop key to restore Display flashing CLE, press start / stop key to restore 1.0~99.0Hz 1~9999 0.01~1.00 1~6 0-30% 0.0-5.0S 0.0-50.0Hz … 1: percentage … 1.0~99.0Hz 1.0~99.0Hz 1.0~99.0Hz 1.0~99.0Hz 1.0~99.0Hz 1.0~99.0Hz 1.0~99.0Hz 1.0~99.0Hz Corresponding frequency of the highest output voltage Segment speed 1 setting 1.0~99.0Hz 1.0~30.0Hz 1.0~99.0Hz 40℃~100℃ Undefined 3: Undefined (customizable) 2: Fault indication 1: Set arrival indication 0: Indication in operation 2: M1 operation / stop, M2 section speed 1: M1 operation / stop, M2 reverse rotation / forward rotation 0: M1 forward rotation / stop, M2 reverse rotation / stop 2: Brake stop 1: Deceleration stop 0: Inertia stop 4: External port 3: Turn reverse when power on 2: Turn forward when power on 1: RS485 (RS485) 0: Panel keyboard control 4: Segment speed input 3: RS485 (RS485) 2: External analog signal input (output voltage is 0-5V) or external potentiometer 1: Panel potentiometer control 0: Panel keyboard control Working frequency Minimum operating frequency Maximum frequency setting Over temperature protection selection Overload protection selection M0 function selection M * function selection Parking method Start/stop source of control Source of working frequency Machine number Rs485 format, ASCII Rs485 baud rate -X.xx -X.xx -8.88 1 1500 1 2 0 0 0 … 1 … 45 45 40 35 25 20 10 5 50 50 1 50 90℃ 0 0 1 0 1 1 96 0:48(4800) 2:192(19200) 1:96(9600) 3:384(38400) 1~255 128 Setting range: 80-128 Maximum frequency limiting voltage ratio 55 Setting range: 25-85 Set the highest frequency voltage ratio of compensation 20 8 7 Setting range: 5.0-30.0Hz Setting range: 5-15 Setting range: 1-15 (corresponding time 5s-0.1s) 7 Factory value Setting range: 1-15 (corresponding time 5s-0.1s) Set compensation maximum frequency Minimum frequency compensation Set stop time Set start time