Edwards Signaling Catalog u Power Supplies and Accessories Remote Booster Power Supplies EBPS6A, EBPS10A MEA 476-91-E Vol.13 Overview Standard Features The Booster Power Supply (EBPS) is a UL 864, 9th Edition listed power supply. It is a 24 Vdc filtered-regulated, and supervised unit that can easily be configured to provide additional notification appliance circuits (NACs) or auxiliary power for Mass Notification/ Emergency Communication (MNEC), as well as life safety, security, and access control applications. • Allows for reliable filtered and regulated power to be installed where needed • Cost effective system expansion • Provides for Genesis and Enhanced Integrity notification appliance synchronization • Supports coded output operation • Self-restoring overcurrent protection • Multiple signal rates • Can be cascaded or controlled independently • Easy field configuration • On-board diagnostic LEDs identify wiring or internal faults • Standard Edwards keyed lockable steel cabinet with removable door • 110 and 230 Vac models available • Accommodates 18 to 12 AWG wire sizes • Optional tamper switch • Dual battery charging rates The EBPS contains the circuitry to monitor and charge internal or external batteries. Its steel enclosure has room for up to two 10 ampere-hour batteries. For access control-only applications, the EBPS can support batteries totaling up to 65 ampere-hours in an external enclosure. The EBPS has four Class B (convertible to two Class A) NACs. These can be activated in one or two groups from the EBPS’s unique dual input circuits. The EBPS is available in 6.5 or 10 ampere models. Each output circuit has a capacity of three amperes; total current draw cannot exceed the unit’s rating. The EBPS meets current UL requirements and is listed under the following standards: Standard (CCN) Description UL864 9th ed.ition (UOXX)Fire Alarm Systems UL636 (ANET, UEHX7) Holdup Alarm Units and Systems UL609 (AOTX, AOTX7) Local Burglar Alarm Units and Systems UL294 (ALVY, UEHX7) Access Control Systems UL365 (APAW, APAW7) Police Station Connected Burglar Alarm Units and Systems UL1076 (APOU, APOU7) Proprietary Burglar Alarm System Units UL1610 (AMCX) Central Station Alarm Unit ULC-S527 (UOXXC) Control Units, Fire Alarm (Canada) ULC-S303 (AOTX7) Local Burglar Alarm Units and Systems (Canada) C22.2 No. 205 Signaling Equipment (Canada) Page 1 of 4 S85005-0125 D ATA S H E E T Not to be used for installation purposes. Issue 5 Application Dimensions The EBPS provides additional power and circuits for notification appliances and other 24 Vdc loads. It is listed for indoor dry locations and can easily be installed where needed. D5 Fault conditions are indicated on the on-board diagnostic LEDs, opening the EBPS input sense circuit and the trouble relay (if programmed). While this provides indication to the host system, the EBPS can still be activated upon command. A separate AC Fail contact is available on the EBPS circuit board, which can be programmed for trouble or AC Fail. There are seven on-board diagnostic LEDs: one for each NAC fault, one for battery fault, one for ground fault, and one for AC power. EBPS NACs can be configured for a 3-3-3 temporal or continuous output. California temporal rate outputs are also available on certain models. This makes the EBPS ideal for applications requiring signaling rates that are not available from the main system. In addition to the internally generated signal rates, the EBPS can also be configured to follow the coded signal rate of the main system NACs. This allows for the seamless expansion of existing NACs. D2 D3 Side View D4 Front View D1 D6 Side View The unique dual-input activation circuits of the EBPS can be activated by any voltage from 6 to 45 VDC (filtered-regulated) or 11 to 33 Vdc (full-wave rectified, unfiltered). The first input circuit can be configured to activate 1-4 of the four possible outputs. The second input circuit can be configured to control circuits 3 and 4. When outputs are configured for auxiliary operation, these circuits can be configured to stay on or automatically deactivate 30 seconds after AC power is lost. This feature makes these circuits ideal for door holder applications. The EBPS also has a separate 200 mA 24 Vdc output that can be used to power internal activation modules. Top View All knockouts for 3/4 in conduit (1.9 cm) D1 D2 D3 D4 D5 D6 17.0 in (43.2 cm) 3.5 in (8.9 cm) 13.0 in (33.0 cm) 6.5 in (16.5 cm) 3.375 in (8.6 cm) 12.0 in (30.4 cm) Wire routing The EBPS enclosure has mounting brackets for up to three Signature modules to the right of the circuit board. Engineering Specification Supply, where needed, Edwards EBPS Series Booster Power Supplies (EBPS) that are interconnected to and supervised by the main system. The EBPS shall function as a stand-alone auxiliary power supply with its own fully-supervised battery compliment. The EBPS battery compliment shall be sized to match the requirements of the main system. The EBPS shall be capable of supervising and charging batteries having the capacity of 24 ampere-hours for Mass Notification/Emergency Communication (MNEC), life safety and security applications, and the capacity of 65 amperehours for access control applications. The EBPS shall provide a minimum of four independent, fully supervised Class B circuits that can be field configurable for notification appliance circuits or auxiliary 24 Vdc power circuits. EBPS NACs shall be convertible to a minimum of two Class A NACs. Each EBPS output circuit shall be rated at 3 amperes at 24 Vdc. Each output circuit shall be provided with automatically restoring overcurrent protection. The EBPS shall be operable from the main system NAC and/or Edwards Signature Series control modules. EBPS NACs shall be configurable for continuous, 3-3-3 temporal or optionally, California rate. Fault conditions on the EBPS shall not impede operation of main system NAC. The EBPS shall be provided with ground fault detection circuitry and a separate AC fail relay. Page 2 of 4 Notes 1. Maintain 1/4-inch (6 mm) spacing between power-limited and nonpower-limited wiring or use type FPL, FPLR, or FPLP cable per NEC. [2] Power-limited and supervised when not configured as auxiliary power. Nonsupervised when configured as auxiliary power. [3] Source must be power-limited. Source determines supervision. 4. When using larger batteries, make sure to position the battery terminals towards the door. S85005-0125 D ATA S H E E T Not to be used for installation purposes. Issue 5 Typical Wiring Single or cascaded booster anywhere on a notification appliance circuit Fire Alarm Control Panel Sense 2 Input Sense 1 Input Existing NAC end-of-line resistors are not required to be installed at the booster’s terminals. This allows multiple boosters to be driven from a single NAC circuit without the need for special configurations. To next signaling device, booster, or EOL resistor NAC Circuit NAC Circuit NAC output #1 NAC output #2 NAC output #3 NAC output #4 Booster Power Supply Configuring the Booster for AC Power Fail delay operation* Multiple E-NAC modules using the EBPS’s sense inputs Notification appliance circuit (NAC) + EOL 47 k E-NAC Module + E-IDC1B Module Data in from previous + + device or Signature controller Data in from previous device or loop controller Data out to next device + + + + Notification appliance circuit (NAC) + UL listed EOL 15 KOhm + IN Sense 1 COM OUT IN Sense 2 COM OUT NO Trouble COM NC EOL 47 K + + + 200 mA AUX Continuous UL listed EOL 15 KOhm + UL listed EOL 15 k Ohm TB5 + Notification appliance circuit (NAC) + IN Sense 1 COM OUT IN Sense 2 COM OUT NO Trouble COM NC Page 3 of 4 NAC1/ AUX1 NAC2/ AUX2 NAC3/ AUX3 NAC4/ AUX4 UL listed EOL 15 k Ohm + TB5 NAC1/ AUX1 NAC2/ AUX2 NAC3/ AUX3 NAC4/ AUX4 200 mA AUX Continuous + Notification appliance circuit (NAC) EOL 47 K + E-NAC Module + E-NAC Module Data out to next device + + + + *The Booster supports AC Power fail delay of three hours via its trouble contact when dip switch SW2-6 is on. All other troubles are reported to supervising module or panel without delay via Sense inputs. S85005-0125 D ATA S H E E T Not to be used for installation purposes. Issue 5 Specifications Model AC Line Voltage Contact us... Phone: 1-800-336-4206 Web: www.edwardssignaling.com Edwards Signaling is an EDWARDS brand. 3 Farm Glen Boulevard Farmington, CT 06032 In Canada, contact Chubb Edwards... Email: inquiries@chubbedwards.com Web: www.chubbedwards.com © 2013 UTC Fire & Security Americas Corporation, Inc. All rights reserved. Specifications subject to change without notice. Edwards is part of UTC Climate, Controls & Security, a unit of United Technologies Corporation. Notification Appliance Circuit Ratings Trouble Relay Auxiliary Outputs Input Current (from an existing NAC) Booster Internal Supervisory Current Booster Internal Alarm Current Signature Mounting Space Maximum Battery Size Terminal Wire Gauge Relative Humidity Temperature Rating NAC Wiring Styles Output Signal Rates Ground Fault Detection Agency Listings 1. 2. 6.5 amp Booster 10 amp Booster 120VAC or 220-240VAC 50/60Hz 120VAC or 220-240VAC 50/60Hz 580 watts 390 watts 3.0A max. per circuit @ 24Vdc 3.0A max. per circuit @ 24Vdc nominal 10A max total all NACs nominal 6.5A max total all NACs 2 Amps @ 30Vdc Four configurable outputs replace NACs 1, 2, 3 or 4. as auxiliary outputs and 200 mA dedicated auxiliary. (See note 2.) 3mA @ 12Vdc, 6mA @ 24Vdc 70mA + 35 mA for each circuit set to AUX 270mA Accomodates three two-gang modules. 10 Amp Hours (2 of 12V10A) in cabinet up to 24 Amp hours with external battery cabinet for fire and security applications; up to 65 Amp hours for access control applications in external battery box. 18-12 AWG 0 to 93% non condensing @ 32°C 32° to 120°F (0° to 49°C) Class A or Class B Continuous, California rate, 3-3-3 temporal, or follow installed panel’s NAC. (See note 1.) Enable or Disable via jumper UL, ULC, CSFM Model EBPS*CAA provides selection for California rate, in place of temporal. Maximum of 8 Amps can be used for auxiliary output. Ordering Information Catalog Number EBPS6A EBPS10A Description Shipping Wt. lb (kg) 13 ( 5.9) 13 ( 5.9) 6.5 Amp Booster Power Supply 10 Amp Booster Power Supply Related Equipment 12V6A5 7.2 Amp Hour Battery, two required 12V10A 10 Amp Hour Battery, two required BC-1 Battery Cabinet (up to 2 - 40 Amp Hour Batteries) BC-2 Battery Cabinet (up to 2 - 17 Amp Hour Batteries) 12V17A 18 Amp Hour Battery, two required (see note 1) 12V24A 24 Amp Hour Battery, two required (see note 1) 12V40A 40 Amp Hour Battery, two required (see notes 1, 2) 12V50A 50 Amp Hour Battery, two required (see notes 1, 2) 12V65A 65 Amp Hour Battery, two required (see notes 1, 2) 1. 2. Requires installation of separate battery cabinet. EBPS supports batteries greater than 24 Amp hours for access control applications only. S85005-0125 D ATA S H E E T Not to be used for installation purposes. Issue 5 06-27-13 Page 4 of 4 3.4 (1.6) 9.5 (4.3) 58 (26.4) 19 (8.6) 13 ( 5.9) 20 (9.07) 32 (14.5) 40 (18.14) 49 (22.2)
