FMX13 10x4 Rigid - Tag Tridem - N3 – contact sales engineering reference application FMX104RFT3A 3179 ,888 Cab 2534 Chassis Dimensions [mm] WB Wheelbase A D N N Overall Chassis Length Center of rear axle to front of body Rear Overhang (Min.) Rear Overhang (Max.) T Y Y Theoretical Wheelbase Center of Gravity for Payload (Min.) Center of Gravity for Payload (Max.) 4300 4350 4600 4900 5100 5600 6000 10965 11315 11415 11715 11865 11515 11465 3735 3785 4035 4335 4535 5035 5435 845 845 845 845 845 845 845 2395 2695 2545 2545 2495 1645 1195 4561 -982 730 4611 -973 760 4861 -959 872 5161 -934 1013 5361 -922 1104 5861 -899 1314 6261 -878 1490 Chassis Weights [kg] Front Axles Rear Bogie Kerb Weight Payload (including body, driver, fuel, etc.) 6705 6680 6690 6665 6665 6700 6710 3980 4035 4070 4130 4160 4120 4135 10685 10715 10760 10795 10825 10820 10845 21315 21285 21240 21205 21175 21180 21155 Turning Diameter [mm] Turning Circle Diameter Kerb to Kerb Turning Circle Diameter Wall to Wall Plated Weights [kg] Gross Vehicle Weight Gross Combination Weight Front Axles Rear Bogie 18100 18200 19000 20000 20600 22200 23500 19500 19700 20500 21400 22100 23700 25000 Plated Design 32000 44000 16000 24000 43000 44000 16000 27000 Important Notes Chassis Dimensions Cab Height: +328 mm for CAB-HSLP, -262 mm for CAB-LDAY, -262 mm for CAB-LSLP, +16 mm for CAB-SLP. Front Axle to Back of Cab: +431 mm for CAB-HSLP and CAB-SLP, -69 mm for CAB-LDAY, +425 mm for CAB-LSLP. D-measure includes a front clearance of 50 mm and for rigid trucks also a subframe of 100 mm. Height can vary ± 20 mm for leaf and ± 10 mm for air suspension. All dimensions are for unladen chassis and any tag axles down. Chassis height used: CHH-HIGH. Rear overhang used for vehicle weight calculation is the maximum rear overhang (N Max.) for selected wheelbase. Height change when chassis height CHH-MED,FRAME300: 0 mm. Chassis weight includes oil, water, AdBlue, 0 litres fuel and without driver. Kerb weight can vary ± 3%. Turning diameters are theoretically calculated. Tag axle used: TA-HYDRS. Legal weights can differ from country to country. For more detailed weight information, including optional equipment weights, ask your Volvo sales contact to enter your specification into the Volvo Weight Information system (WIS). Do NOT use this drawing for bodybuilding. Refer to Volvo Bodybuilder Instructions and chassis assembly drawing FMX104RFT3A. Weight and dimensions are based upon the following tyres: Front Axle Tyres: 315/80R22.5 Drive Axle Tyres: 315/80R22.5 Trailing/Pusher Axle Tyres: 315/80R22.5 1 (7) Ref: FMX104RFT3A 01 GBR 2022-11-29 ENG FMX13 10x4 Rigid - Tag Tridem - N3 – contact sales engineering reference application □ RTH2610B Drive Axles - RTH2610B 26-tonne hub reduction tandem with TRUCK USE FMX104RFT3A □ RC-ROUGH □ RC-SMOOT Road conditions - On / off-road Road Conditions - Smooth □ TIPP-PRE □ UNIFORM Transport Adaption - Tipper vehicle preparation Transport Adaption - Basic platform vehicle □ RTH2610F CORE COMPONENTS □ CHH-HIGH □ CHH-MED □ CHH-XHIG Chassis Height - High - for loading heights check the unique BEP chassis drawing attached to this quote Chassis Height - Medium - for loading heights check the unique BEP chassis drawing attached to this quote Chassis Height - X-High - for loading heights check the unique BEP chassis drawing attached to this quote ■ TA-HYSBS Tag axle - Electro-hydraulically steered □ RADDT-G2 Rear air suspension - 3 axles - 2 driven/1 tag, high ground clearance Rear air suspension - 3 axles - 2 driven / 1 tag □ RADDT-GR ■ FMX-DAY5 □ FMX-HSL5 □ FMX-LDA5 □ FMX-LSL5 □ FMX-SLP5 Emission level - Euro VI step E Emission level - Euro VI step E ■ D13S420A Engine - New D13K420 12.8 litre developing 420hp at 141800rpm. Peak torque 2100Nm at 860 -1400rpm. Engine - New D13K460 12.8 litre developing 460hp at 141800rpm. Peak torque 2300Nm at 900-1400rpm. Engine - New D13K500 12.8 litre developing 500hp at 141800rpm. Peak torque 2500Nm at 1000-1400rpm. Engine - New D13K540 12.8 litre developing 540hp at 141800rpm. Peak torque 2600Nm at 1000-1450rpm. □ D13S460A □ D13S500A □ D13S540A ■ □ □ □ D13K420 D13K460 D13K500 D13K540 □ EBR-EPGC □ EBR-VEB+ ■ AT2612 □ ATO2612 □ ASO-C □ ASO-ULC □ FP-D13+ Fuel Package + □ DRIVE5 □ DRIVE5+ □ DRIVE5++ Cab Package - Drive Cab Package - Drive + Cab Package - Drive ++ □ 1LIVINFM □ 2LIVINFM Sleep & Resting Package - Living one-bed Sleep & Resting Package - Living two-bed □ □ □ □ □ Basic media package without secondary display Media Information Platform with Dynafleet Support Media Information Platform - Medium level Media Information Platform with Navigation Media Information Platform with Navigation & Volvo Connect "On board" Support INFOBAS INFODF INFOMED INFONAV INFONDF □ VISIX5 □ VISIXCAM Visibility Package □ SAFE22 □ SAFE22+ Safety package Safety Package + □ CHASPAC Chassis Package Rigid CHASSIS D13K420 - 420hp engine D13K460 - 460hp engine D13K500 - 500hp engine D13K540 - 540hp engine □ FST-AIR ■ FST-PAR □ FST-PAR3 Front suspension type - Air Front suspension type - 2 leaf parabolic springs Front suspension type - 3 leaf parabolic springs □ FSLS-BAS Front suspension levelling - basic stroke ■ FAL16.0 □ FAL18.0 Front axle design capacity - 16 tonnes - 2 x 8 tonne front axles Front axle design capacity - 18 tonnes - 2 x 9 tonne front axles - check tyre load index Front axle design capacity - 20 tonnes - 2 x 10 tonne front axles - check tyre load index □ FAL20.0 Engine Brake Type - Exhaust pressure governor for I shift gearbox Engine Brake Type - Volvo engine brake + and exhaust pressure governor, enhanced performance from additional exhaust rocker control. Retardation 375kW Gearbox - AT2612 12-speed "I-Shift" automated mechanical suitable for gross train weights up to 60 tonne only. Refer to sales engineering when used in conjunction with a PTO Gearbox - ATO2612F 12-speed I-Shift overdrive automated mechanical, suitable for gross train weights up to 100 tonne. Refer to sales engineering when used in conjunction with a PTO Crawler gear Ratio direct top gearbox 19:1 Ratio Overdrive gearbox 17:1 Ultra low crawler and crawler gear Ratios direct top gearbox 32:1 and 19:1 Ratios Overdrive box 32:1 and 17:1 ■ Standard Equipment ■ RTS2370A PACKAGES Cab - Day - with steel safety cage design Designed and built to Swedish impact and ECE R29 regulations Cab - Globetrotter - with steel safety cage design Designed and built to Swedish impact and ECE R29 regulations Cab - Low Day - with steel safety cage design Designed and built to Swedish impact and ECE R29 regulations Cab - Low Sleeper - all-steel safety cage design. Built to Swedish impact and ECE R29 regulations Cab - Sleeper - with steel safety cage design Designed and built to Swedish impact and ECE R29 regulations □ EU6HT ■ EU6SCR □ RTS2310A differential and cross locks* - design GCW 100tonne, 4 planetary gears * Cross locks replaced by a dog clutch if tandem axle lift is specified. Drive Axles - RTH2610F 26-tonne hub reduction tandem with differential and cross locks* - design GCW 100tonne * Cross locks replaced by a dog clutch if tandem axle lift is specified. Drive Axles - RTS2310A 23-tonne single reduction tandem with differential and cross locks*- design GCW 100tonne * Cross locks replaced by a dog clutch if tandem axle lift is specified Drive Axles - RTS2370A 23-tonne single reduction tandem with differential and cross locks*- design GCW 70tonne * Cross locks replaced by a dog clutch if tandem axle lift is specified □ FSM-LUB Front suspension maintenance - Lubricated rear shackles on pins and bushings □ FSTAB ■ FSTAB2 □ FSTAB3 Front anti-roll bar - Normal stiffness Front anti-roll bar - Medium stiffness Front anti-roll bar - High stiffness ■ RAL27 □ RAL33 □ RAL36 Rear bogie design capacity - 27 tonne Rear bogie design capacity - 33 tonne Rear Bogie Design Capacity - 36 tonne ■ RSTAB3 Rear anti-roll bar - Stiff ■ □ □ □ Rear-axle load limiter - 10.5 tonne - speed controlled Rear-axle load limiter -11.5 tonne - speed controlled Rear-axle load limiter - 13 tonne Rear-axle load limiter - 9.5 tonne RALIM105 RALIM115 RALIM13 RALIM95 ■ ASF-DL1 □ ASF-DL3 Air suspension with 1 driving level Air suspension with 3 driving levels □ ACTST-TO Active Steering- Volvo Dynamic Steering - VDS - with extra electronic pump and torque overlay □ ASFE-BAS Active steering feature - Basic - Volvo Dynamic Steering - VDS - only □ Optional Equipment For more detailed information about cab and powertrain equipment, please refer to separate specification sheets. For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the Volvo Sales Support system (VSS). The factory reserves the right to modify design and change equipment without previous notification. The specification can vary from country to country. 2 (7) Ref: FMX104RFT3A 01 GBR 2022-11-29 ENG FMX13 10x4 Rigid - Tag Tridem - N3 – contact sales engineering reference application FMX104RFT3A □ ASFE-OG Active steering feature - Volvo Dynamic Steering - VDS - with □ ASFE-PO □ ASFE-PS ■ PSP-VAR □ PSP-VAR2 stability assist - oversteer Active steering feature - Volvo Dynamic Steering - VDS - with personal settings and stability assist Active steering feature - Volvo Dynamic Steering - VDS - with personal settings Power steering pump - Variable displacement Power steering pump - Variable displacement with electronic control ■ EBS-MED Brake package - EBS medium including "hill" hold function □ AUXPARK Auxiliary parking brake - Additional spring brakes ■ RST-AIR Rear suspension type - Air ■ FRAME300 Chassis frame section external height - 300 mm ■ FST8080 Chassis frame thickness - 8 mm web and flange ■ FIL-EEEB □ FIL-EEEF Chassis frame inner liner - From the end of the engine to the end of the bogie Chassis frame inner liner - From the end of the engine to end of the frame ■ BBOX-L Battery box position - Left hand side □ 2BAT210B ■ 2BAT210C Battery Capacity - 2 x 210 Ah - Gel type Battery Capacity - 2 x 210 Ah - AGM Absorbent Glass-fibre Material type ■ BATTAMP □ BATTIND Battery management - Voltage and current gauge Battery management - Voltage, current and charge indicators □ ADR2 ADR Adaptation - For transportation of dangerous goods on the road - Note does NOT include safe loading pass package if required this is quoted separately □ MSWI-A ■ MSWI-C □ MSWI-R Battery master switch - ADR switch circuit shut down Battery master switch - Chassis mounted toggle by the battery box Battery master switch - Key fob operated remote controlled □ SUP-BAS □ SUP-LOW Side guards - Check with bodybuilder chassis space requirements EC approved low chassis side guards □ CHAIN-S Snow chains □ HOOK-SC Snow chain hooks ■ TOWF-HD1 Front towing device - One heavy-duty front towing device □ TOWMBRH Towing member, high mounted in centre of frame, D = 190 □ TOWMBRL1 Towing member, low mounted under the frame □ TOWMBRM Towing member, medium mounted in line with frame lower flange ■ RFEC-S □ RFEC-U Rear frame profile - Straight cut Rear frame profile - Slight uppercut for tippers □ □ □ □ □ Towing coupling, Ringfeder 4040A Towing coupling, Ringfeder 5050A Towing coupling, Rockinger 400 G-150 for 40mm eyes Rockinger RO 50 50mm for centre axle trailer VBG 795V-3 coupling (centre axle trailer) C-RI4040 C-RI5050 C-RO400G C-RO50 C-VBG795 □ TOWR-ONE Towing hitch attached to rear crossmember □ □ □ □ □ TREL-PK TREL14 TREL15 TREL7 TREL7-7 Trailer electrical preparation kit - chassis/cab wiring Single 14 pole electrical trailer connector Trailer electrical connection - Single 15 pin - ADR certified 7 pole - 24N trailer electrical suzie Trailer electrical connection - 2 x 7 pin - 24N and 24S □ TBC-DUO □ TBC-EC Trailer brake connections - Duomatic type Trailer brake connections - EC palm coupling connectors □ TRBR-HCF □ TRBR-STA Full pressure hand controlled trailer brake Stationary trailer brake control □ TRB-STRE Stretch Brake - Automatic low speed trailer brake activation to avoid jack-knifing and improve steerability □ FFEND-B □ FFEND-T Standard mounted mud wings on second front axle Transport mounted mud wings on second front axle □ RFEND-B □ RFEND-T Rear mud wings - Three piece EC approved and spray flaps Rear mud wings - Temporary on drive axle for transport delivery only □ RFH-BAS □ RFH-HIG □ RFH-LOW Basic rear wing height High rear wing height - higher wing tops Lower rear wing height - shallower wing tops □ ATANK-AL ■ ATANK-ST Air tanks - Aluminium Air tanks - Steel ■ UR-FUEL Right fuel tank - Without Min volume 255l Max volume 810l ■ UL-FUEL Left fuel tank - Without Min volume 160l Max volume 450l □ ADTP-L □ ADTP-LF ■ ADTP-R Adblue tank position - Chassis mounted on the left-hand side Adblue tank position - Chassis mounted on the left-hand side between axle 1 and 2 Adblue tank position - Chassis mounted on the right-hand side □ TL-LED Rear lights - LED □ ADB032 □ ADB048 □ ADB064 Plastic AdBlue tank - 32 litres Plastic AdBlue tank - 48 litre Plastic AdBlue tank - 64 litre □ BLIGHT-E Emergency brake light □ ADTC-BF AdBlue tank cover with satin alloy look decorative cover □ RT-AL ■ FCAP-L Diesel and AdBlue filler cap - Locking □ RT-ALDP ■ FUFF-AS □ FUFF-ATS Fuel filler - Anti-spill device Fuel filler - Anti-spill & anti-syphon device □ RT-ALDPD □ ■ □ □ Exhaust - Horizontal silencer - left outlet Exhaust - Horizontal silencer - rear outlet Exhaust - Horizontal silencer - right outlet Exhaust - Horizontal silencer - vertical outlet □ RT-ALDU □ EXST-SSP □ EXST-ST Stainless steel exhaust stack - NOT polished Steel exhaust stack □ WHC-FIX2 □ WHC-FOL2 Wheel chocks - Two fixed design Two foldable wheel chocks □ WHCP-F □ WHCP-R □ WHCP-T Wheel chock carrier position - In the front part of the vehicle Wheel chock carrier position - In the rear part of the vehicle Wheel chock carrier position - Outer luggage locker □ TB-L80 □ TB-R80 ESH-LEFT ESH-REAR ESH-RIGH ESH-VERT WHEELS & TYRES ■ RT-STEEL Wheels - Alcoa brushed aluminium rims - standard holes for long stud fixing Wheels - Alcoa Dura-Bright aluminium rims - standard holes for long stud fixing Wheels - Alcoa Dura-Bright EVO aluminium rims - countersunk holes for short stud fixing Wheels - Alcoa brushed aluminium rims - countersunk holes for short stud fixing Wheels - Steel rims □ WCAP Aerodynamic hub caps □ SPWT-D □ SPWT-F Spare wheel & tyre with rear tyre pattern Spare wheel & tyre with front tyre pattern □ SWCP-LF □ SWCP-T □ SWCP-TP Spare wheel carrier on left side of chassis ahead of rear axle Spare wheel supplied temporarily strapped to chassis Temporary spare wheel carrier on top of chassis frame Toolbox 800 mm, left side □ JACK-12T □ JACK-15T □ JACK-20T 12 tonne bottle jack 15 tonne bottle jack 20 tonne bottle jack Toolbox 800 mm, right side ■ TOOL-BAS Toolkit - Basic ■ Standard Equipment □ Optional Equipment For more detailed information about cab and powertrain equipment, please refer to separate specification sheets. For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the Volvo Sales Support system (VSS). The factory reserves the right to modify design and change equipment without previous notification. The specification can vary from country to country. 3 (7) Ref: FMX104RFT3A 01 GBR 2022-11-29 ENG FMX13 10x4 Rigid - Tag Tridem - N3 – contact sales engineering reference application FMX104RFT3A □ TOOLKIT Toolkit - Complete □ HPG-F101 Parker F1-101 gearbox mounted, fixed displacement, single □ INFLAHOS Tyre inflation hose □ GAUGE-TP Tyre pressure gauge □ HPG-F41 □ HPG-F51 DRIVELINE EQUIPMENT □ HPG-F61 flow, hydraulic pump Parker F1-41 gearbox mounted, fixed displacement, single flow, hydraulic pump Parker F1-51 gearbox mounted, fixed displacement, single flow, hydraulic pump Parker F1-61 gearbox mounted, fixed displacement, single flow, hydraulic pump Parker F1-81 gearbox mounted, fixed displacement, single flow, hydraulic pump □ TRAP-HD Reinforced gearbox application ■ DRM-BE □ DRM-E Drive Mode - Balanced & Economy Drive Mode - Economy □ HPG-F81 □ PVT-MAP I-See Predictive Cruise Control - using map based topography information ■ STWPOS-R Steering wheel position - RIGHT-HAND DRIVE □ STWM-LE Steering wheel - Leather rim □ STGW-AD2 ■ STGW-ADJ Steering wheel adjustment - Neck tilt, column height and angle Steering wheel adjustment - Column height and angle □ AIRBAG Driver air bag □ INST-BAS Basic level instruments ■ DRC-AMII DPF Regeneration control switch - for manual and switching off regeneration ■ 1DAYDIG2 Tachograph - Continental VDO 4.0 □ ARSL Additional road speed limit - switch in dashboard □ ESP-BAS1 Electronic Stability Control ESC □ ESPC-RO Additional ESC functions - Reduced / Off □ HWSS-ACB ■ CRUIS-E □ CRUIS-E5 Cruise control - with I-roll and I-cruise, controls in steering wheel Eco torque software - Improved economy mode. Fuel economy optimized cruise control for I-Save □ AMSO-AUT Enhanced I-shift software with manual shift available in auto mode and kickdown facility on accelerator pedal □ AVO-ENH I-Shift application software - Construction and off road applications □ APF-ENH I-shift enhanced PTO functions □ CD43-O Clutch - 430mm twin plate □ TC-MAOH2 □ TC-MWO Extra high performance transmission oil cooler - air to oil with front mounted radiator Basic transmission oil cooler - water to oil □ 2COM1100 □ 2COMP870 ■ 2COMP900 Air compressor - Two-cylinder 1100 litres per minute Air compressor - Two-cylinder 870 litres per minute Air compressor - Two-cylinder 900 litres per minute □ HWSS-FCB Adaptive cruise control ACC with forward collision warning and AEBS advanced emergency brake system Forward collision warning with AEBS advanced emergency brake system □ CLU-AIRC Clutchable air compressor □ LSS-DW Lane departure-warning system ■ AIRIN-HI □ AIRIN-LO Air intake - Roof-mounted behind cab on the left-hand side Low level air intake behind cab on left hand side □ LCS □ LCS4 Lane change support Side Collision Avoidance Support - passenger and driver side □ ACL1ST-S Air filter - two-stage element □ DAS-W Driver Alert Support system ■ □ □ □ □ Alternator capacity - 110 amp Alternator capacity - 150 amp Alternator capacity - 180 amp Alternator capacity - 110 amp Alternator capacity - 150 amp □ RSENS-W Rain sensing windscreen wipers □ CU-ECC □ CCV-C ■ CCV-OX Closed crankcase engine ventilation Closed crankcase ventilation for cold markets ■ CU-MCC Cab Climate Unit - Electrically controlled air conditioning with sun sensor Cab Climate Unit - Electrically controlled air conditioning with a carbon filter, sun, mist, and air quality sensor Cab Climate Unit - Manual air conditioning ■ IMMOBIL Thatcham H2 approved immobiliser ■ PRIM-EL □ PRIM-MAN Electrical priming pump Manual priming pump □ ALARM-E Vehicle alarm - Cab plus external sensor for body/trailer □ BUPMON Back up monitor - Digital reverse camera, parameter & lead supplied loose in cab. 24A110BL 24A150BL 24A180BL 24AL110B 24AL150B □ CU-ECC2 □ AF-R Hot fuel recirculation heated fuel filter ■ FUEFE2LW □ FUEFE2SW Large engine mounted dual fuel filter with water separator Small engine mounted dual fuel filter with water separator □ PHONE-PK Telephone preparation kit (antenna, antenna attachm. cable incl.) □ EST-AID Engine starting aid -Preheating element in the air inlet manifold □ 220EBH15 220V/1.5Kw electric engine block heater □ ISUNS-BS ■ ISUNS-DS Side sun visor - Driver & passenger side Side sun visor - Driver-side □ PTER-DIN Engine power-take-off - Rear-mounted with DIN5462 (female) splined shaft for a close-coupled pump Models with 3 steering axles will use this to drive the steering pump (AUXPSP) □ □ □ ■ Interior front sun visor without mirror Interior front sun visor with mirror on driver side Electrically operated textile interior sun blind Manually operated textile interior sun blind □ HPE-V45 Parker VP1-45, variable displacement, single flow, engine mounted hydraulic pump Parker VP1-75, variable displacement, single flow, engine mounted hydraulic pump □ ADFS Two extra DIN slots in front shelf - can be fitted with card or drawer available as an accessory ■ BUPALARM Reverse alarm □ RTOLL-PK Road toll PREPARATION kit for trucks operating with "Toll Collect" in Germany □ LOADIND Load indicator with central dashboard display □ REMC-MF Multi-functio wireless remote control □ FIREXT3S Fire extinguisher - 3kg mounted on the seat base □ WARNVEST High visibility warning vest - no sleeves □ HPE-V75 □ PTR-D □ PTR-DH □ PTR-DM □ PTR-F □ PTRD-D □ PTRD-F Gearbox PTO for plug-in pump, 0.71xeng speed Gearbox driven high speed PTO for one plug-in hydraulic pump Gearbox driven medium speed PTO for one plug-in hydraulic pump Gearbox driven PTO with rear flange connection Gearbox driven HIGH SPEED PTO for two plug-in hydraulic pumps PTO with 1 DIN + 1 flange connection rear, manual gearbox ■ Standard Equipment ISUNF-B ISUNF-MD ISUNF-RE ISUNF-RM □ Optional Equipment For more detailed information about cab and powertrain equipment, please refer to separate specification sheets. For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the Volvo Sales Support system (VSS). The factory reserves the right to modify design and change equipment without previous notification. The specification can vary from country to country. 4 (7) Ref: FMX104RFT3A 01 GBR 2022-11-29 ENG FMX13 10x4 Rigid - Tag Tridem - N3 – contact sales engineering reference application FMX104RFT3A □ AIDKIT First aid kit - Legal demand for EU markets including delivery □ COFMA-PK Coffee maker - Preparation kit. to EU bodybuilder First aid kit - Legal demand for trucks transiting Germany □ WARNLAMP Portable warning lamp ■ INLI-BAS □ INLI-NL □ INLI-NLD Interior light - White LEDs Interior light - White and red nightlight LEDs without dimmer Interior light - White and red nightlight LEDs with dimmer □ LAMP-IN Inspection lamp □ ARL-FLEX Flexible reading lamps - Two "snake" type □ BULBKIT Bulb and fuse kit □ WRITEPAD Writing pad ■ RH-EE □ RH-ER ■ DST-CF4 Driver seat - Suspended, adjustable shock absorber, travel, backrest & lumbar controls with integrated seatbelt Driver seat - Suspended with adjustable shock absorber, travel, backrest, lumbar & heat controls with integrated seatbelt Driver seat - Suspended with adjustable shock absorber, travel, backrest, lumbar, heat and ventilation controls with integrated seatbelt Fixed tinted glass sky window with emergency exit Steel roof hatch - Electrically operated, rear opening with emergency exit Tinted glass roof hatch - Electrically operated, rear opening with emergency exit Tinted glass roof hatch - Manually operated, rear opening with emergency exit □ AIDKIT1B □ DST-CF5 □ DST-CF6 □ SBD-RED Seat belt colour - Red □ SBPRE-DS Driver seat belt pretensioner □ PST-BAS1 □ PST-CF4 □ PST-CF5 ■ PST-STD2 □ PST-STD4 Passenger seat - Fixed non suspended fold up with seatbelt mounted on cab "B" post Passenger seat - Suspended, adjustable shock absorber, travel, backrest & lumbar controls with integrated seatbelt Passenger seat - Suspended with adjustable shock absorber, travel, backrest, lumbar & heat controls with integrated seatbelt Passenger seat - Fixed with backrest adjustment, non suspended with seatbelt mounted on cab "B" post Passenger seat - Standard suspended with seatbelt mounted on cab "B" post □ SBPRE-PS Passenger seat belt pretensioner □ ARMRE-BB □ ARMRE-DB □ ARMRE-PB Armrests - Two on both driver & passenger seats Armrests - Two on the driver seat Armrests - Two on the passenger seat □ ARU-BAS □ ARU-LEA Armrest upholstery - Vinyl Armrest upholstery - Leather ■ GRABHI-B Instep cab grab handle - Steel finish ■ FMAT-RUB □ FMAT-TX2 Footwell floor mats - Rubber Footwell floor mats - Two sets, Rubber and textile with an embossed pile supplied in the cab □ LBK70 Lower bunk - Fixed 700 x 2000 mm □ MATL-FI □ MATL-SF Lower mattress - Firm pocket sprung Lower mattress - Flexi-zone semi-firm, pocket springs up to 100kg - 16 stone □ OLMAT-BA □ OLMAT-PR Mattress overlay protector - 35mm thick Mattress overlay protector - Premium 50mm thick □ TBK60F □ TBK70F Top bunk - Fixed foldable 600 x 1900mm Top bunk - Fixed foldable 700 x 1900mm □ PH-CAB2 □ PH-ENGCA □ PH-SS Cab parking heater -1.8kW Air to air Cab parking heater - Engine and cab Cab parking heater - Short stop □ SLCP-BAS □ RH-ETR □ RH-MTR ■ GLAS-TIN Cab windows - Tinted □ SWIND-BS □ SWIND-PS Cab side window - On both sides behind 'B' post Cab side window - Left side behind 'B' post □ AWIND-RF Rear window □ VANMIR Vanity mirror - In front shelf □ AS-FUS Extra shelf in front compartments □ INFOT-PK TV mounting preparation kit - Above the driver's door, includes bracket, electrical and speaker connections CAB EXTERIOR ■ DGLAS-H □ DGLAS-L Door glass - Hardened Door glass - Laminated ■ LOCK-CTL □ LOCK-REM Door locks - Central locking with key Door locks - Remote central locking ■ BUMP-HD Front bumper - Heavy duty - FMX □ AUXFS Lower swinging cab step □ GUARD-EH Sump and radiator guard - to protect engine and hoses ■ BUGNET Radiator insect screen □ CTILTP-E ■ CTILTP-M Electrically operated hydraulic cab tilt Manually operated hydraulic cab tilt □ FCABS-A ■ FCABS-M Front cab suspension - Air Front cab suspension - Mechanical spring □ RCABS-A ■ RCABS-M Rear cab suspension - Air Rear cab suspension - Mechanical spring □ MIRCFCPX Mirrors - Electrically heated and operated - FMX- main and wide-angle with manually adjusted kerb view mirror on the passenger side and position camera in nearside mirror arm. To increase direct vision to the side the main mirrors have no cowlings Electrically heated and operated -FMX- main and wide-angle mirrors with manually adjusted passenger kerb mirror, to increase direct vision to the side the main mirrors have no cowlings ■ MIRCOMFX ■ AMIR-F20 Auxiliary front view mirror with a 200mm radius Sleeper control panel - Basic with switches for interior light, night heater, roof hatch and door lock □ SUNV-H External smoke grey sunvisor □ AD-ROOF Cab roof deflector - Adjustable Storage on engine tunnel - Central document box with two rear cup holders Storage on engine tunnel - Central document box with two rear cup holders & open storage pocket on cab rear wall Storage on engine tunnel - Open storage pocket on cab rear wall □ AD-SIDES Cab side deflector - Short extension panels ■ HL-BASIC Headlamps - Halogen □ HL-CLEAN Head lamp cleaner - washer jets □ HLP-ST Headlamp protection □ RUS-BAS □ RUS-HIG Rear cab upper storage - 300 mm high Rear cab upper storage - 440 mm high - volume 245 litres □ HL-ADJ Headlight adjustment - Switch in cab □ REF-ICPK □ REFR-RUS Fridge - Engine tunnel mounted preparation kit Fridge - 28 litre rear upper wall mounted with dividers ■ UDRIVL Auxiliary driving lights - Without □ ASL-RF2 Two Hella H11 70W spotlamps in Globetrotter sign box □ MICRO-PK Microwave equipment - Wiring preparation kit for oven □ BOTH-D Bottle holder - One under dashboard centre section □ BEACOA2F □ BEACOA2R □ BEACON-P Roof beacons - Two front roof mounted amber LED Roof beacons - Two rear roof mounted amber LED Roof beacons - switch and wiring preparation only □ ETSB-F □ ETSB-FR □ ETSB-R ■ Standard Equipment □ Optional Equipment For more detailed information about cab and powertrain equipment, please refer to separate specification sheets. For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the Volvo Sales Support system (VSS). The factory reserves the right to modify design and change equipment without previous notification. The specification can vary from country to country. 5 (7) Ref: FMX104RFT3A 01 GBR 2022-11-29 ENG FMX13 10x4 Rigid - Tag Tridem - N3 – contact sales engineering reference application FMX104RFT3A □ BEACONA4 Roof beacons - Four amber LED - two front/ two rear □ RBA-T2 Lower rear body attachments for helper frame □ CRANEPK1 Crane plates mounted to frame, for cranes up to 10 tonne metre capacity Crane plates mounted to frame, for cranes up to 20 tonne metre capacity Crane plates mounted to frame, for cranes up to 40 tonne metre capacity □ CABPT-R1 ■ CABPT-R2 Single outlet for roof mounted accessories Twin outlets for roof mounted accessories. □ SPOTP-F □ SPOTP-R □ SPOTP-RF Spotlamp preparation in front, max 280W Spotlamp preparation on roof, max 280W Spotlamp preparation on cab roof and in cab front, max 2x280W □ CRANEPK2 □ ROS-IL2 □ AUXL-SPK Electrical preparation kit - wiring and switch for snow plough lights □ ROS-ILP Preparation kit for illuminated roof sign with switch loose in cab, fit after registration Roof sign illumination preparation kit □ CSGN-FMX "Volvo FMX" headboard logo □ TAILPRE2 □ TAILPREP Tail lift preparation kit, wireless remote operation Taillift preparation kit - cab switch and warning in driver display ■ HORN-F1S □ HORN-R2S Horn - Air single tone - chassis mounted Horn - Air - Two roof-mounted □ AESW2 □ ANT-CBR Roof mounted antenna for CB radio, single aerial. Only Globetrotter cabs brings in extra DIN slots. Two Body builder bistable electrical switches (marked AUX1 / AUX2) 2 Body builder bistable el.switches (marked AUX1/AUX2) and prep. for 4 more switches □ □ □ □ □ □ □ Front, middle & rear roof mounted accessory brackets Front roof mounted accessory bracket Front & middle roof mounted accessory brackets Front & rear roof mounted accessory brackets Middle roof mounted accessory bracket Rear roof mounted accessory bracket Rear & middle roof mounted accessory brackets ACCBR-AP ACCBR-F ACCBR-FM ACCBR-FR ACCBR-M ACCBR-R ACCBR-RM □ REFS-TW □ REFS-TY □ CRANEPK4 □ AESW2PK □ AUXSW-4 DELIVERY SERVICES White cab conspicuity markings by packed in cab Yellow cab conspicuity markings by packed in cab SUPERSTRUCTURE PREPARATIONS □ SRWL-PK □ SWL-2FW □ SWL-2RW □ SWL-4W □ SWL-PK □ WLC-H2A □ WLC-H2W □ WLC-PKCH □ WLC-PKH □ WLC-PKL □ WLC-PKLH ■ TGW-4GWL Telematics gateway - GSM/GPRS/4G modem, LTE & WLAN □ FMS-PK Fleet Management System gateway - required for aftermarket telematics □ DRUT1 Driver utility app - "My Truck" - 1 year subscription For mobile phone, tablet, with android and IOS systems. Only available with Volvo Connect subscription Driver utility app - "My Truck" - 2 year subscription For mobile phone, tablet, with android and IOS systems. Only available with Volvo Connect subscription Driver utility app - "My Truck" - 3 year subscription For mobile phone, tablet, with android and IOS systems. Only available with Volvo Connect subscription Driver utility app - "My Truck" - 4 year subscription For mobile phone, tablet, with android and IOS systems. Only available with Volvo Connect subscription Driver utility app - "My Truck" - 5 year subscription For mobile phone, tablet, with android and IOS systems. Only available with Volvo Connect subscription □ DRUT2 Chassis-mounted working lamps - Side work and reverse lamp preparation and 3 position switch - Max load 280W Chassis-mounted working lamps - Two white front-mounted LED lamps Chassis-mounted working lamps - Two white rear-mounted LED lamps Chassis-mounted working lamps - Four white front and rearmounted LED lamps Chassis-mounted working lamps - Side work lamp preparation and 2 position switch - Max load 280W □ DRUT3 □ DRUT4 □ DRUT5 Two H3/70W working lamps with amber coloured lens high mounted back of cab Two H3/70W white working lamps high mounted on the back of cab Working lamp back of cab - Preparation kit - cables and switch Preparation kit, cables and switch for high mounted working lamps back of cab Preparation kit, cables and switch for low mounted working lamps back of cab Preparation kit - cables and switch for low and high mounted working lamps back of cab. □ ECBB-HIG ■ ECBB-MED Body builder electrical centre with body builder module □ BBCHAS1 □ BBCHAS3 One 7-pole connector for Body builder interface Three 7-pole connectors for Body builder interface □ BEPR-T2 Body builder electrical software preparation for tipper with remote control □ EXSTER External steering control - Volvo dynamic steering and bodybuilder module prepared for external control system, installed and computer by bodybuilder □ TD-BAS ■ TD-LED Trailer detection WITHOUT LED sensing Trailer detection with LED sensing □ FRFS-BS Frame rail free space - both sides to give space for crane legs or other equipment. □ FBA-BTF □ FBA-BTSF Lower front body attachments for torsionally flexible - platform body Lower front body attachments for torsionally semi-flexible body - box or curtainsider □ HBA-FSFB □ HBA-SB Holes for body attachments - flexible/semi-flexible body Holes for body attachments - stiff body ■ Standard Equipment Wiring for 4 extra switches (from Body builder electrical centre to switch positions) □ Optional Equipment For more detailed information about cab and powertrain equipment, please refer to separate specification sheets. For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the Volvo Sales Support system (VSS). The factory reserves the right to modify design and change equipment without previous notification. The specification can vary from country to country. 6 (7) Ref: FMX104RFT3A 01 GBR 2022-11-29 ENG FMX13 10x4 Rigid - Tag Tridem - N3 – contact sales engineering reference application FMX104RFT3A ■ Standard Equipment □ Optional Equipment For more detailed information about cab and powertrain equipment, please refer to separate specification sheets. For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the Volvo Sales Support system (VSS). The factory reserves the right to modify design and change equipment without previous notification. The specification can vary from country to country. 7 (7) Ref: FMX104RFT3A 01 GBR 2022-11-29 ENG
