1 A 2 3 4 5 6 7 Installation instructions 8 194R-NX12 To be commissioned and maintained only by qualified personnel; pay attention to the operating instructions! Montageanleitung Inbetriebsetzung und Wartung nur durch Fachpersonal; Betriebsanleitung beachten! Instructions de montage Mise en service et entretien: seulement par du personnel spécialisé ; respecter les instructions d’exploitation! Istruzioni per il montaggio Messa in servizio e manutenzione solo da personale specializzato; attenersi alle istruzioni per l’esercizio! Instrucciones de montaje ¡Puesta en servicio y mantenimiento exclusivamente por personal especializado; respetar las instrucciones de puesta en servicio y mantenimiento! ATTENTION: To prevent electrical shock, disconnect from power source before installing or servicing. Install in suitable enclosure. Keep free from contaminants. ACHTUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. ATTENTION: Avant le montage et la mise en service, couper l'alimentation secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée. Protéger le produit contre les environnements agressifs. ATTENZIONE: Per prevenire infortuni, togliere tensione prima dell'installazione o manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti. ATENCION: Desconéctese de la corriente eléctrica, antes de la instalación o del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada. Manténgalo libre de contaminantes. B IMPORTANT: Mount handle on a flat surface for Type 3, 3R, 4, 4X and 12 enclosures WICHTIG: Für Gehäuse Typ 3, 3R, 4, 4X und 12 Hebel auf ebener Fläche montieren IMPORTANT: Pour les coffrets de types 3, 3R, 4, 4X et 12 monter la poignée sur une surface plane IMPORTANTE: Montare la maniglia su una superficie piatta per le custodie tipo 3, 3R, 4, 4X e 12 IMPORTANTE: Monte el mando en una superficie plana para las cajas del tipo 3, 3R, 4, 4X y 12 C Mounting of 190-HS1, -HS4, -HS1E, -HS4E + 194R-NX12 + 140M-D-HA Montage von 190-HS1, -HS4, -HS1E, -HS4E + 194R-NX12 + 140M-D-HA Montage des 190-HS1, -HS4, -HS1E, -HS4E + 194R-NX12 + 140M-D-HA Montaggio di 190-HS1, -HS4, -HS1E, -HS4E + 194R-NX12 + 140M-D-HA Montaje de 190-HS1, -HS4, -HS1E, -HS4E + 194R-NX12 + 140M-D-HA Keep hold of Festhalten Maintenir fixement Afferrare Sujetar 1 D 2 3 T8 1 N.m (9 lb-in) 7 E 4 3mm 3 N.m (26 lb-in) X 6 2.8 N.m (25 lb-in) 5 9 8 ON O F F R e se t X F G REFERENCE REVISION AUTHORIZATION 1 1001714 DIMENSIONS APPLY BEFORE SURFACE TREATMENT THIS DRAWING IS THE PROPERTY OF ROCKWELL INTERNATIONAL CORPORATION OR ITS SUBSIDIARIES AND MAY NOT BE COPIED, USED OR DISCLOSED FOR ANY PURPOSE EXCEPT AS AUTHORIZED IN WRITING BY ROCKWELL INTERNATIONAL CORPORATION (DIMENSIONS IN INCHES) TOLERANCES UNLESS OTHERWISE SPECIFIED .XX: N/A .XXX: N/A H LOCATION: MILWAUKEE, WISCONSIN U.S.A. G. Ushakow CHKD. M. Jutz APPD. T. Houck DR. ANGLES: 41053 N/A E - DOC BULLETIN 194R-NX12 INSTALLATION INSTRUCTION SHEET DATE DATE DATE 11-24-03 11-24-03 11-24-03 DWG. SIZE B SHEET 1 OF 2 41053-270 B-vertical.ai 1 2 3 A 4 5 6 7 8 Mounting of 190-HS1, -HS4, -HS1E, -HS4E pos. horizontal Montage von 190-HS1, -HS4, -HS1E, -HS4E querlage Montage des 190-HS1, -HS4, -HS1E, -HS4E pos. horizontale Montaggio di 190-HS1, -HS4, -HS1E, -HS4E pos. horizontale Montaje de 190-HS1, -HS4, -HS1E, -HS4E pos. horizontal R L B 3 3 1 1 2 2 C 4 4 5 5 6 6 D clic clic 7 7 Keep hold of Festhalten Maintenir fixement Afferrare Sujetar Keep hold of Festhalten Maintenir fixement Afferrare Sujetar E 8 8 9 F 9 T8 1 N.m (9 lb-in) T8 1 N.m (9 lb-in) 41053-270-01 (1) Printed in U.S.A. -01 1 TWO SIDES PRINTED BODY STOCK WHITE BODY INK BLACK PART NO. CHG. LTR. MATERIAL G 1 1001714 2-1/8" W x 2-3/4" H FLAT FOLD SIZE REFERENCE REVISION AUTHORIZATION 8-1/2" W x 11" H DIMENSIONS APPLY BEFORE SURFACE TREATMENT THIS DRAWING IS THE PROPERTY OF ROCKWELL INTERNATIONAL CORPORATION OR ITS SUBSIDIARIES AND MAY NOT BE COPIED, USED OR DISCLOSED FOR ANY PURPOSE EXCEPT AS AUTHORIZED IN WRITING BY ROCKWELL INTERNATIONAL CORPORATION (DIMENSIONS IN INCHES) TOLERANCES UNLESS OTHERWISE SPECIFIED .XX: N/A .XXX: N/A H LOCATION: MILWAUKEE, WISCONSIN U.S.A. G. Ushakow CHKD. M. Jutz APPD. T. Houck DR. ANGLES: 41053 N/A E - DOC BULLETIN 194R-NX12 INSTALLATION INSTRUCTION SHEET DATE DATE DATE 11-24-03 11-24-03 11-24-03 DWG. SIZE B SHEET 2 OF 2 41053-270 B-vertical.ai